Ultrasound imaging without the gel

- Advertisement -spot_imgspot_img
- Advertisement -spot_imgspot_img

As a demonstration, the team fixed a small wearable patch, about the size of a key fob, to a volunteer’s neck. The patch contained a small ultrasound probe, and the dry and stretchy layer that stuck directly to the skin. The entire patch was connected to a small portable tablet that recorded the patch’s ultrasound images as the volunteer took a 30-minute bike ride, from MIT’s campus in Cambridge, Massachusetts, to Bunker Hill in neighboring Charlestown, and back. 

“We are really aiming to address a material challenge in ultrasound imaging,” says study leader Shu Wang, a postdoc in MIT’s Department of Mechanical Engineering.

“If you don’t have a good interface, that will definitely stop you from developing this wearable imaging field,” adds co-lead author and MIT postdoc Runze Li. “This is a very good solution that enables a longer time for imaging.”

In addition to Zhao, Wang, and Li, the study’s MIT co-authors are Chen Gong and Won Jun Song; additional co-authors are Zihan Tang and Ying Li of the University of Wisconsin at Madison; Chwee Teck Lim of the National University of Singapore; and Xiaodong Chen of Nanyang Technological University in Singapore. Zhao, Chen, and Lim are the co-lead principal investigators of the SMART WITEC interdisciplinary research group.

Molecular detangler

Gels and liquids in general are ideal media through which sound waves, including ultrasound, can travel. Think of sonar, and the calls of whales and dolphins, which can travel much farther in water than air. This is mainly due to the makeup of molecules in fluids. Water molecules, for instance, are small and loosely connected, and can slide easily against each other. As a sound wave passes through, there is little friction between the molecules, allowing the wave to travel without losing intensity. 

Soft solids such as most rubbery and polymer-based materials, however, have more interconnected molecular structures. The same sound wave would dissipate when moving through a solid block, as larger, tangled molecules would generate more friction as they shift in response to the incoming wave. 

The MIT team aimed to make a solid, rubbery material that retained a gel’s ultrasound propagating properties. For this, they took a molecular engineering approach. 

“Hydrogel is mainly water, with just a bit of polymer, whereas solid materials like rubber are almost 100 percent polymer molecules,” Wang explains. “We tried to reduce the friction between polymer chains in our material, without adding liquid or lubricant.”

Polymer materials such as rubber and elastic are made from microscopic molecules that chemically bond with other similar molecules to form long polymer chains. In a solid material, these chains form a dense thicket and do not slide easily against each other. 

In looking for ways to reduce the friction between polymer chains, the engineers landed on a “bottlebrush” structure — a molecular configuration that has been explored in other applications including drug delivery and light-reflecting materials. A bottlebrush molecule consists of a main backbone of molecules, with smaller side chains of molecules sprouting away, like the bristles of a pipe cleaner. 

“These hairy extensions don’t easily penetrate other bottlebrush molecules,” Wang notes. “They can easily move around at the ultrasound frequencies, and that’s why there is less friction between them.”

With that reasoning, the team came up with a protocol to fabricate a polymer material made entirely from a molecular bottlebrush architecture. Their first attempts, however, did not quite hold up. 

“The first samples were very soft and crumbly, like tofu,” Wang says. “If the samples were too large, they would not hold their own weight, and if you picked one up, it would just break.”

They quickly found they could reinforce the material by chemically fusing it with a second, loosely connected network of bottlebrush molecules. This additional network essentially held the first, crumbly network of bottlebrush polymers in place, without affecting their low-friction properties. The result was a tougher, rubbery material that the researchers were able to stretch repeatedly without tearing. 

“It’s very much like skin,” says Wang. “It’s very soft but will hold together if pinched or pulled.” 

Imaging workouts

The team fabricated credit card-sized samples of the new material and first tested its ultrasound properties on a “phantom” model — a synthetic structure that is made from materials that mimic a human’s skin and internal structures. In these tests, the material efficiently transmitted ultrasound waves from a probe, through the model, to image the structures underneath. The team kept the setup running continuously and found it kept imaging clearly for around nine days. 

“In principle, this material could go forever, depending on how stable it is,” Wang notes. “The sound properties stay the same. And that was the moment when we thought, oh, this material could work.”

To test the material’s mechanical performance, the team adhered a patch to a volunteer’s chest as they ran on a treadmill. For comparison, the volunteer also wore a sample of a conventional silicone rubber. Throughout a 10-minute run, the silicone rubber became water-logged with sweat, whereas the new material wicked away any sweat buildup. These tests suggest that the new material can hold up over strenuous exercise. 

Finally, the researchers tested the material in the field, attaching it to a small ultrasound transducer applied to a volunteer’s neck. Throughout a 30-minute bike ride that traversed steep inclines, the device maintained continuous and accurate ultrasound imaging of the rider’s blood flow. 

Going forward, the team is working to streamline the fabrication of the material. Then, they hope to enable wearable, long-lasting ultrasound imagers that can be used to track athlete performance and monitoring patient health outside of clinical settings.

“In the hospital, a doctor can replace gel if it dries out,” Li offers. “But if we want ultrasound imaging that goes beyond the clinical scenario, we need a material that lasts longer, and is easier to handle. And we think this really works.”

This work was supported, in part, by the Singapore-MIT Alliance for Research and Technology and the MIT Health and Life Sciences Collaborative.

Source link

- Advertisement -spot_imgspot_img

Highlights

- Advertisement -spot_img

Latest News

- Advertisement -spot_img